Security Link SL150 Manual de instalación Pagina 1

®UL325compliantcompliantUL991LISTED®USSL-100DC & SL-150DC Installation ManualCopyright © 2008 all-o-matic inc. www.allomatic.net WWW.ALLOMATIC.NET

9GATE TRAVEL ADJUSTMENTFOR SL-150DCLocate limit switch box.Step 1: Make sure operator is not running .Step 2: Use a screw driver to pull limit lock pl

10Right hand and left hand opening is from behind the operator.OPENING DIRECTION SETTINGSOpeningOpening0210OOUURRNN338866BBSS331133OOUURRNN338866BBSS3

11230V230V115V115VGRDLINE 1LINE 2All gate operators be properly grounded.A proper ground in a gate operator installation minimizes or prevents damage

1/4 IN1/4 IN1 1/2 INSAFETY LOOPWHEN USEDEXIT LOOP4 FT 4 FT8 FT8 FT4 FT4 FT4 FTGATE OPERATORGATEGATE TRACKTWISTED 6 TURNS PER FOOTWIRED IN SERIESThis

The following loop installation guidelines are for installing typical driveway loops for access control applications (i.e. parking gates, sliding gate

14CCPowerPowerDetectDetectLoop FailLoop FailResetReset22110000SENS.SENS.LEVELLEVELBOOST ONBOOST ONPULSEPULSEFREQ.FREQ.0000OFFOFFPRESPRES221111 22 33 4

15SAFETY LoopdetectorPHOTO BeamRelay (N.C.)MULTIPLE SAFETY DEVICES CONNECTIONSMultiple devices installed together must be connected in series . th

This is a loop . Remember when connecting to an All-O-Matic circuit board from loop detector theYou must twist your wires from your exit point of

17LEADING EDGE CONNECTIONLEADING EDGE SENSORConnect one of the wires from leading edge and/or one of the grey wires from a wireless edge receiver to

18N.C.COMTHREE BUTTON STATIONSYSTEMConnect the from all the push buttonsto input on the board.Connect push button contact toinput on the board.C

TABLE OF CONTENTSImportant safety instructions...Different UL 325 class types...

19MASTER/SLAVE CONNECTIONUse a two wire shielded cable and run it through a UL listed conduit for master/slave connection. Follow the wiring diagram

20MEICAGN TL KOCSOLENOIDLOCKStep DownTransformerMAGNETIC/SOLENOID LOCK CONNECTIONSMagnetic lock installation requires a step down transformer with app

21RADIO RECEIVER CONNECTIONS3 wire receiver: mounts on receiver strip outside control box as shown below.4 wire receiver: connect the two relay wires

22OPEN AND CLOSE ELECTRONIC REVERSING SENSOR(ERDs) ADJUSTMENTMAX MAXMIN MINSENSITIVITYCounter clockwise maximumsensitivityClockwise minimum sensitivit

231 2 3 4 5 6 7 81 2 3 4 5 6 7 8-----------------------OPEN-------------------------------------------

24DIP SWITCH FUNCTIONSTIMERTIMER switch “ON” activates the TIMER. See page 21 for details.RADIORADIO switch “ON” allows the radio receiver to override

25SOLAR PANEL CONNECTIONDR127-33043CL07 EC8RBL4MC68 AI2 M12214202300206 40100120M10101001MAAFS21B802360GBONOOUURRNN338866BBSS331133OOUURRNN338866BBSS3

LED DIAGNOSTICSAC/PWR ON: Will be lit when AC power is ON.M/S LINK: Will be lit when master/slave communication is active.ALARM: Two states.1st state:

EMERGENCY RELEASEProcedures to release gate for .1. Turn power OFF.2. Push pedal down & move pedal slightly to the left to hold pedal down in

IMPORTANT SAFETY INSTRUCTIONSTo reduce the risk of WARNINGinjury:READ THE FOLLOWING DIRECTIONS. DO NOT EVEN THINK OF STARTING UNTIL YOU HAVE READ AN

*Confirm that the gate operator being installed is appropriate for the application.*Confirm that the gate is designed and built according to current p

Class one: ResidentialA vehicle gate operator intended for use at a home of one to four single family dwellings, garages or parking area.Class Two: Co

523½”23 ”½4”6.5”CONCRETE PAD PLACEMENTFOR SL-100DC24”24”9½”9½”24”24”10”10” RED HEAD BOLTSFOUR PLACES ½”X 3 ½” Area for conduit(s) Operator concrete pa

6CONCRETE PAD PLACEMENTFOR SL-150DC24”24”16.25”16.25”30”30”7.5”7.5”FOUR RED HEAD BOLTS ½”X 3 ½” Area for conduit(s) GATE TRACK GATEGATE TRACKFOOTINGMi

7Rear mount installation and chain layoutA front mount installation and chain layoutDRIVEWAYDRIVEWAYDIFFERENT INSTALL CONFIGURATIONSGate in open posit

8Gear boxGATE TRAVEL ADJUSTMENTFOR SL-100DCLimit nut lock plateLimit nutsLocate limit switchesStep 1: Stop the gate operator using the three button st