Security Link SL150 Guía para resolver problemas Pagina 110
- Pagina / 144
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SL150 Installation and Setup Guide
21–2
– Hayes Smartmodem Optima 2400
– Hayes Optima 2400 Fax96
– Hayes Smartmodem 1200 External Modem
– Hayes Smartmodem 1200B Internal Modem (Rev. 1.2 or higher)
– Hayes external
Optima 24 Plus FAX96 Modem
– Practical
Peripherals PM14400FXSA
COMPASS® Downloader Software (at revision level supporting the
SL150
)
Appropriate interconnecting cables
Initial Download
For initial downloading, enter
[Installer code] + # + 5
. This sets field
✱
95 to 4 rings, and
system to “no call-back” option. The download computer can then call the subscriber, make
the connection, and download all programming items.
After the control and the PC have established valid communication, each keypad on the
system will become inactive and will display “
CC
” or “
MODEM COMM
.” The control,
however, will still be scanning its zones and looking for alarms. If an alarm does occur, after
communication is broken off, alarms are sounded and the proper dialer reports are sent to
the Central Station. The keypads will become active after the download communication is
terminated. The detailed operation of the download functions is covered in the installation
instructions for the COMPASS Downloader.
Remote Programming Commands
The downloading system can perform many functions when in communication with the
control unit. Besides uploading and downloading, the status of the system can be observed
and various commands can be initiated, as follows:
•
Arm the system in the AWAY mode; disarm the system.
•
Bypass a zone.
•
Force the system to accept a new program download.
•
Shut down communication (dialer) functions (in response to nonpayment of monitoring fees
in an owned system).
•
Shut down all security system functions (in response to nonpayment for a leased system).
•
Inhibit local keypad programming (prevents account takeover).
•
Command the system to upload a copy of its resident program to the office.
•
Read: arming status, AC power status, lists of faulted zones, bypassed zones, zones
currently in alarm, zones currently in trouble, and RF sensors with low-battery conditions.
Note:
One of the following messages will be displayed following an upload:
Alpha Keypads Fixed-word Keypads
Upload failed dF
Upload completed dC
Remote Programming Advisory Notes
•
Alarm and trouble reporting may be delayed during the time that the system and the
downloader are linked to each other following a valid exchange of codes, but the proper
message will get through to the Central Station after the link is broken.
•
Keypad entries are ignored during the time interval stated above.
•
A copy of the program downloaded may be produced from the IBM PC-compatible
computer, using the product's internal report generator, when an optional printer is
connected (consult your PC manual for proper printer and connections).
- 6HF XULW\6\VWHP 1
- Table of Contents 4
- List of Figures 7
- Introduction 9
- FINAL POWER 12
- Installing the Control 13
- RCVR BRD 15
- TERMINALS 16
- ON CONTROL 16
- Wiring the AC Transformer 17
- Installing the Backup Battery 18
- Earth Ground Connections 18
- Installing Remote Keypads 19
- Mounting the Keypads 20
- AUX. DATA 21
- Basic Hardwired Zones 1–8 23
- Remote Keyswitch (Zone 7) 27
- Wired Zone Expansion 33
- Wireless Expansion 37
- 1 2 3 4 5 38
- Installing the 5800TM Module 39
- Jam Detection and Reporting 39
- Appendix A 42
- Powerline Carrier Devices 47
- Programming Relay Outputs 48
- 4285 & 4286 VIP Module 49
- Section 11: 50
- Audio Alarm 50
- Verification (AAV) Unit 50
- 4285/4286 51
- VIP MODULE 51
- External Sounders 53
- Sounder Connections and Power 54
- Sounder Supervision 54
- Testing the Sounder 54
- Long Range Radio 55
- Dynamic Signaling Feature 56
- 4285 or 4286 58
- Final Power-Up 59
- Battery Tests 60
- Mechanics of Programming 61
- Loading Factory Defaults 63
- Exiting the Programming Mode 63
- Data Field Descriptions 69
- OUTPUT TO LONG RANGE RADIO 74
- Allows 81
- Zone Programming 83
- 86
- To Remove a Zone 88
- Section 16 -Zone Programming 91
- Output Device Programming 93
- Zone Lists 99
- Alpha Descriptor Programming 101
- Adding Custom Words 103
- ALPHA VOCABULARY LIST 105
- CHARACTER (ASCII) CHART 105
- Macros (SpeedKey) 107
- Remote Programming and 109
- Control (Downloading) 109
- Remote Programming Commands 110
- Initial Download 110
- System Communication 111
- System Operation 115
- Keypad Functions 116
- Testing the System 121
- Troubleshooting Guide 123
- POSSIBLE CAUSE REMEDY 124
- SYMPTOM POSSIBLE 124
- CAUSE REMEDY 124
- CONTACTING TECHNICAL SUPPORT 125
- In This Section 127
- APPENDIX A 131
- Regulatory Agency Statements 133
- Warnings and Limitations 135
- DOC LOAD NO.: 3 143
- ¬19'l 144
- Two Mid America Plaza 144
- Suite 200 144
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Security Link SL150
(29 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales