Security Link SL150 Guía para resolver problemas Pagina 21
- Pagina / 144
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Section 3 – Installing Remote Keypads
3–3
Make connections directly to the screw terminals as shown in Figure 7. Make no connection to the
keypad blue wire (if present).
Be sure to connect the negative (–) terminal on the Power Supply unit to terminal 4 (AUX
–
) on the
control.
+
–
+
456 7
SUPPLEMENTARY
POWER SUPPLY
–
CONTROL TERMINAL STRIP
AUX.
AUX. DATA
IN
DATA
OUT
IMPORTANT:
MAKE THESE
CONNECTIONS
DIRECTLY TO
SCREW
TERMINALS AS
SHOWN.
TO KEYPAD RED WIRE
TO KEYPAD BLK WIRE
TO KEYPAD YEL WIRE
TO KEYPAD GRN WIRE
TO KEYPAD BLK WIRE
TO KEYPAD RED WIRE
TO KEYPAD GRN WIRE
TO KEYPAD YEL WIRE
Figure 7. Using a Supplementary Power Supply for Keypads
Preliminary Checkout Procedure
To verify that the system is working before connecting field wiring from zones and devices, do
the following:
1.
Temporarily connect a 2000-ohm end-of-line resistor across each of the basic hardwired
zones 1–8, as shown in the
SL150
Summary of Connections diagram.
Without actual zone wiring or
EOL resistors
connected, the keypads will not display the
“Ready” message.
2.
Power up the system temporarily by plugging the AC transformer (previously wired to
the control) into a 120VAC outlet.
Busy
–
Standby
(on alpha keypads) or
dI
(on fixed-word keypads) will be displayed
3.
Wait approximately 1 minute. At that time, the green READY LED should light, and the
words
READY ENTER CODE
(on fixed-word keypads), or
SYSTEM READY
(on alpha
keypads) should be displayed.
To bypass the 1-minute delay, press
#
plus
0
.
If the “Ready” message does not appear on any of the keypads in the system, or a “Not
Ready” message is displayed, check the keypad wiring connections, and make sure each of
the 8 basic hardwired zones has a 2000 ohm resistor connected across its terminals.
When a
READY
message is displayed on the keypad(s), the system is functioning properly.
Do not remove the EOL resistors until you are ready to make connections to the hardwired
zones, to allow for testing later in the manual.
If an
OC
or
OPEN-CIRCUIT
message is displayed on the keypad, data from the control is not
reaching the keypad. Check the wiring.
- 6HF XULW\6\VWHP 1
- Table of Contents 4
- List of Figures 7
- Introduction 9
- FINAL POWER 12
- Installing the Control 13
- RCVR BRD 15
- TERMINALS 16
- ON CONTROL 16
- Wiring the AC Transformer 17
- Installing the Backup Battery 18
- Earth Ground Connections 18
- Installing Remote Keypads 19
- Mounting the Keypads 20
- AUX. DATA 21
- Basic Hardwired Zones 1–8 23
- Remote Keyswitch (Zone 7) 27
- Wired Zone Expansion 33
- Wireless Expansion 37
- 1 2 3 4 5 38
- Installing the 5800TM Module 39
- Jam Detection and Reporting 39
- Appendix A 42
- Powerline Carrier Devices 47
- Programming Relay Outputs 48
- 4285 & 4286 VIP Module 49
- Section 11: 50
- Audio Alarm 50
- Verification (AAV) Unit 50
- 4285/4286 51
- VIP MODULE 51
- External Sounders 53
- Sounder Connections and Power 54
- Sounder Supervision 54
- Testing the Sounder 54
- Long Range Radio 55
- Dynamic Signaling Feature 56
- 4285 or 4286 58
- Final Power-Up 59
- Battery Tests 60
- Mechanics of Programming 61
- Loading Factory Defaults 63
- Exiting the Programming Mode 63
- Data Field Descriptions 69
- OUTPUT TO LONG RANGE RADIO 74
- Allows 81
- Zone Programming 83
- 86
- To Remove a Zone 88
- Section 16 -Zone Programming 91
- Output Device Programming 93
- Zone Lists 99
- Alpha Descriptor Programming 101
- Adding Custom Words 103
- ALPHA VOCABULARY LIST 105
- CHARACTER (ASCII) CHART 105
- Macros (SpeedKey) 107
- Remote Programming and 109
- Control (Downloading) 109
- Remote Programming Commands 110
- Initial Download 110
- System Communication 111
- System Operation 115
- Keypad Functions 116
- Testing the System 121
- Troubleshooting Guide 123
- POSSIBLE CAUSE REMEDY 124
- SYMPTOM POSSIBLE 124
- CAUSE REMEDY 124
- CONTACTING TECHNICAL SUPPORT 125
- In This Section 127
- APPENDIX A 131
- Regulatory Agency Statements 133
- Warnings and Limitations 135
- DOC LOAD NO.: 3 143
- ¬19'l 144
- Two Mid America Plaza 144
- Suite 200 144
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Security Link SL150
(29 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales