Security Link SL150 Guía para resolver problemas Pagina 62
- Pagina / 144
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SL150 Installation and Setup Guide
13–2
Entering Program Mode
You may use one of the following methods:
a) Press [
✱
] and [#] keys at the same time within 50 seconds after power is applied to the
control; or
b) After power-up, enter 4 1 1 2 (Installer code) + 8 0 0.
This method is disabled if you exit the Program mode using
✱
98 instead of
✱
99. See the
paragraph titled, Exiting the Program Mode, later in this section.
If a different Installer code is subsequently programmed, use it instead of 4112 to gain
access to the Programming mode.
When you enter the Program mode, data field
✱
20 will be displayed (this is the first data field
in the system). The system will now accept entries for field
✱
20.
Programming a Data Field
1. Press [
✱
] + [Field No.] (for example,
✱
22), then make the required entry.
2. When you have completely programmed a data field, the keypad will beep three times and
then automatically display the next data field in sequence. To go to a different field, press
[
✱
] plus the desired field number.
3. If the number of digits that you need to enter in a data field is less than the maximum
digits available (for example, the phone number field), enter the desired data, then press
[
✱
] and the next data field number to be programmed.
4. If you try to enter a non-existent field, the keypad will display EE or ENTRY ERROR.
Simply re-enter [
✱
] plus a valid field number.
Reviewing a Data Field/Erasing an Entry
Press [#] + [Field No.]. Data will be displayed for that field number. No changes will be
accepted in this mode.
To delete an entry in a field, press [
✱
] + [Field No.] + [
✱
] (applies only to fields
✱
40
το
✱
44,
✱85, ✱86, ✱87, ✱
88, and
✱
94).
Interactive Mode Programming (
✱
56,
✱
58,
✱
80,
✱
81,
✱
82)
Typical prompt displayed
during Interactive mode
programming:
Enter Zn Num.
(00 = Quit) 01
Press [
✱
]
+
[Interactive Mode No.]
(for example,
✱
56). The
alpha keypad will display the first of a series of prompts
requesting entries.
A detailed procedure (with displays of prompts) is provided in
later sections of this manual.
Zone Number
Interactive Mode Used to Program
✱
56 Zone Programming
Zone characteristics, report codes,
alpha descriptors and serial numbers
✱
58
Expert Mode
5800 Series Transmitter serial and
loop numbers
✱
80 Relay Programming
4229 or 4204 Relay modules, or
Powerline Carrier devices
✱
81 Zone List
Programming
Zone lists for relay/powerline carrier,
assignment of chime zones, and Pager
1 and 2 reporting zones
✱
82 Alpha Programming
Zone alpha descriptors
- 6HF XULW\6\VWHP 1
- Table of Contents 4
- List of Figures 7
- Introduction 9
- FINAL POWER 12
- Installing the Control 13
- RCVR BRD 15
- TERMINALS 16
- ON CONTROL 16
- Wiring the AC Transformer 17
- Installing the Backup Battery 18
- Earth Ground Connections 18
- Installing Remote Keypads 19
- Mounting the Keypads 20
- AUX. DATA 21
- Basic Hardwired Zones 1–8 23
- Remote Keyswitch (Zone 7) 27
- Wired Zone Expansion 33
- Wireless Expansion 37
- 1 2 3 4 5 38
- Installing the 5800TM Module 39
- Jam Detection and Reporting 39
- Appendix A 42
- Powerline Carrier Devices 47
- Programming Relay Outputs 48
- 4285 & 4286 VIP Module 49
- Section 11: 50
- Audio Alarm 50
- Verification (AAV) Unit 50
- 4285/4286 51
- VIP MODULE 51
- External Sounders 53
- Sounder Connections and Power 54
- Sounder Supervision 54
- Testing the Sounder 54
- Long Range Radio 55
- Dynamic Signaling Feature 56
- 4285 or 4286 58
- Final Power-Up 59
- Battery Tests 60
- Mechanics of Programming 61
- Loading Factory Defaults 63
- Exiting the Programming Mode 63
- Data Field Descriptions 69
- OUTPUT TO LONG RANGE RADIO 74
- Allows 81
- Zone Programming 83
- 86
- To Remove a Zone 88
- Section 16 -Zone Programming 91
- Output Device Programming 93
- Zone Lists 99
- Alpha Descriptor Programming 101
- Adding Custom Words 103
- ALPHA VOCABULARY LIST 105
- CHARACTER (ASCII) CHART 105
- Macros (SpeedKey) 107
- Remote Programming and 109
- Control (Downloading) 109
- Remote Programming Commands 110
- Initial Download 110
- System Communication 111
- System Operation 115
- Keypad Functions 116
- Testing the System 121
- Troubleshooting Guide 123
- POSSIBLE CAUSE REMEDY 124
- SYMPTOM POSSIBLE 124
- CAUSE REMEDY 124
- CONTACTING TECHNICAL SUPPORT 125
- In This Section 127
- APPENDIX A 131
- Regulatory Agency Statements 133
- Warnings and Limitations 135
- DOC LOAD NO.: 3 143
- ¬19'l 144
- Two Mid America Plaza 144
- Suite 200 144
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Security Link SL150
(29 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales